App Release Notes
Release notes for MOCREO Smart System, covering firmware, app, portal, and device update history.
v1.7.0
MOCREO Smart App ·
Notes
- This update introduces the SD1 multi-probe sensor, scenario-based alerts, and a redesigned home view that shows the status of every device at a glance.
New Features
- SD1 Sensor Support: Added support for the SD1 multi-probe sensor — two temperature/humidity probes and a door sensor on one device, with full setup, details, alert rule, and firmware update support.
- Scenario-Based Alerts: Choose a usage scenario (refrigerator, freezer, custom, and more) during setup, and the App creates the matching alert rules automatically. No manual threshold setup is needed to start monitoring.
- Guardian View: The Home page has been redesigned. Safe ranges for all devices are shown together, devices that need attention are listed first, and you can generate an AI health report for a room and receive it by email.
- Firmware Updates for More Devices: MS3 and SD1 can now be updated directly from the App.
- Important Event Email Subscription: Subscribe to email notifications for important events from the Settings page.
Improvements
- Smarter Device Setup: Devices can now be found automatically over Bluetooth, and the general scan entry sends each device to the right setup flow based on what the device supports.
- More Flexible Alert Rules: The false-alarm delay can now be set for each probe separately, humidity ranges can be typed in directly, and custom scenarios accept temperatures below zero.
- Clearer Water Sensor Status: Water leak and water level sensors now show "Normal / No Water" when everything is fine.
- Hub Information: The Hub page now shows which Wi-Fi network the Hub is connected to.
- Clearer Setup Messages: Messages shown after scanning an unsupported or unrecognized QR code are now more specific, with a direct link to contact support.
Bug Fixes
- Feedback Attachments: Fixed an issue where attachments could not be uploaded when submitting feedback.
- Back Button: Fixed cases where the back button did not work correctly on setup, Bluetooth discovery, and feedback pages.
- Firmware Version Check: Fixed a case where a device could still prompt for an update after it was already up to date.
- Verification Code Input: Fixed an issue where invalid characters could be entered or pasted into the verification code field.
- Display Details: Fixed text, layout, and prompt issues across setup, alert rule, and device pages.
Compatibility Notes
- Existing devices do not need to be added again, and historical data will not be lost.
- On iOS, critical alerts require the system "Critical Alerts" permission. The App will guide you if it is not enabled.
- Scenario-based alert rules are defaults only; they can be changed at any time on the alert rules page.
v1.6.0
MOCREO Smart App ·
Notes
- This update focuses on improving historical data views, device management, the device setup flow, and overall stability.
New Features
- Multi-Device Data Comparison: View temperature and humidity trends for multiple devices or probes on the same page.
- MS3 Sensor Support: Added support for MS3 temperature and humidity sensors, with QR code setup.
- Hub Details Page: Added a dedicated Hub details page for clearer Hub status, firmware version, connected devices, and offline reminders.
- Family Member Display: Added family member display on the Profile page for quicker viewing and management.
Improvements
- History Chart Performance: History charts now open faster, and repeated views of the same time range are smoother.
- Device Setup Flow: Improved QR code scanning guidance to reduce confusion when an incorrect QR code is scanned.
- First Data Upload Handling: After some devices are added, the App now waits automatically for the first data upload to reduce manual steps.
- Error Messages: Improved messages for Bluetooth interruptions, setup failures, and unrecognized QR codes.
- Temperature Alert Settings: Added support for entering more precise temperature values directly.
- Chart and Comparison Views: Improved device selection, scrolling, time switching, and data display in history charts and comparison pages.
- Sensor Details Page: Added a last report time indicator to make data update timing clearer.
Bug Fixes
- Historical and Comparison Data: Fixed cases where historical data or comparison data could be duplicated or show inconsistent units.
- Calibration Consistency: Fixed cases where historical charts, details pages, and exported data could show inconsistent values after calibration.
- Member Permissions: Fixed cases where some restricted pages could be accessed under certain member permissions.
- Probe Status Updates: Fixed cases where the App status did not refresh promptly after probes were connected or disconnected.
- Device Status Display: Fixed inaccurate status display for some offline, low-battery, and probe-abnormal devices.
- Settings Save State: Fixed cases where page status could display incorrectly after some device settings failed to save.
- Push Popups After Logout: Fixed an issue where push popups could still appear after logging out.
- UI Details: Fixed text, color, button feedback, and prompt details across multiple pages.
Compatibility Notes
- Existing devices do not need to be rebound.
- Historical data will not be lost after updating.
- Account and device pairing methods remain unchanged.
v1.5.0
MOCREO Smart App ·
New Device Support
- Added Support for New Models: Officially compatible with NS3 (Dual-Probe Temperature Sensor) and LB1 (Smart Alarm Buzzer).
- Setup Optimization (LS1/LS2): Added a "Can't scan?" manual setup entry for LS1 and LS2 devices, providing an alternative Bluetooth & LoRa pairing path if QR code scanning is unavailable.
New Features & Updates
- Interactive Data Charts: Added new time-range filters (1H / 1D / 1W / 1M / 1Y) and supported dual-finger zoom and drag interactions for more detailed and intuitive data viewing.
- NS3 Dual-Probe Management:
- Independent Probe Settings: Users can now name, set alert rules, and select scenarios for each probe separately.
- New device cards on the Home page for clear, multi-channel data visualization.
- LB1 Smart Buzzer Integration:
- New device cards for quick status checks.
- Dedicated control page supporting parameter configuration, alarm dismissal, and device testing.
- Alarm System Enhancement: Upgraded the alarm notification logic to support selecting either a Hub or the new LB1 as the sound-alert device, offering more flexible placement for audible alarms.
- Regional Localization: Added a Country/Region selection setting for better localized asset management.
- Improved Settings Consistency: Standardized the configuration interface for alert rules, data calibration, and history data across different device models for a more intuitive user experience.
Bug Fixes
- MS2 Battery Display: Optimized the battery measurement and display logic for MS2 sensors under low-power conditions.
- ST8 Alert Rule Sync: Improved the synchronization logic for ST8 alert rules to ensure consistency between the App settings and the server.
v1.4.0
MOCREO Smart App ·
New Features
- New Device Models: Added support for LD1, MS2, and H6 Lite devices.
- Device Diagnostics (v2.0): Enhanced device anomaly diagnosis with weight display and type differentiation. Defined L0/L1/L2 diagnostic workflows to improve troubleshooting processes across different scenarios.
- QR Code Setup Flow: Unified setup process with support for manual SN input. Added context-aware navigation based on different scanning scenarios.
- LS1/LS2 Compatibility: Implemented compatibility handling for new and legacy LS1/LS2 devices. Setup flow automatically detects device version based on QR code scan result (SN for legacy devices, fingerprint for new devices) and routes to the appropriate setup process. Legacy devices retain firmware upgrade functionality while new devices do not.
- LS2 Special Batch Handling: Added Contact Us prompt for specific LS2 batches when probe is not connected.
- Dismiss (v2.0): Enhanced dismiss functionality with multi-channel alarm information retrieval to address the issue where users without notification permissions couldn't see dismiss popups. Implemented cross-asset dismiss and multi-device dismiss synchronization.
- Rule Settings: Added door sensor rules and adjusted rule arrangement styles.
- Shop Module: Introduced comprehensive shopping features including:
- Shop homepage with ad carousel, secondary category display, and product listings
- Product detail pages with image gallery, product descriptions/specifications, and related product recommendations
- Shopping cart with temporary cart ID registration, supporting query/modify/delete operations and checkout redirect to MOCREO Shop
- Profile Enhancement: Added promotional carousel banner.
- Global Features: Added announcement popup dialog.
Improvements
- Home Page: Redesigned device cards and replaced message icon with member management icon in the top-right corner. Weather information now refreshes each time the home page is accessed. Disabled guide tour.
- Device Management: Improved device setup and management workflows with better compatibility handling and diagnostic capabilities.
v1.3.0
MOCREO Smart App ·
New Features
- SMS Notification Support: Added support for receiving alarm notifications via SMS (Initial support for LW1 devices).
- Account Management: Added the ability for users to modify their bound email address directly within the App.
- Critical Alerts: Added support for Critical Alerts to ensure high-priority notifications are delivered even when the phone is muted or in Do Not Disturb mode.
- New UI/UX: Introduced new interactive elements and page designs for a better user experience.
Improvements
- Hub Beep Settings: Optimized the configuration logic for Hub buzzers and added prompts when selecting offline Hubs.
- Setup Guidance: Added a prompt to configure sensor alerts immediately after successfully adding a new Hub.
- Data Export: Optimized the time format display (12-hour/24-hour) in exported data files.
- SMS Interaction: Improved the validation logic and error prompts for phone number binding and verification codes.
Bug Fixes
- Account Security: Fixed a security issue where other devices logged into the same account could still modify configurations after the account password was changed on the primary device.
- Notification Reliability: Fixed an issue where push notifications might occasionally fail to arrive on iOS devices.
- Alert Logic: Fixed an issue where LW1 devices might display duplicate alert data after triggering an alarm.
- Dismiss Interaction: Fixed an issue where the "Dismiss" popup would not appear or behave incorrectly in certain scenarios (e.g., when push notifications are disabled).
- Data Synchronization: Fixed issues where asset information (Nickname/Email) was not syncing correctly across the App and email notifications after modification.
- UI Display: Fixed a display glitch where the border color would change abnormally on the LW1 history page.
- Legacy Support: Removed irrelevant "Sounds" settings on the interface for older NS1 hardware versions.
- Connection Stability: Fixed an issue where the App required a restart to recover after a socket disconnection.
v1.2.1
MOCREO Smart App ·
Notes
- Fixed known issues to enhance app stability.
v1.2.0
MOCREO Smart App ·
Notes
- New Features
- Support for LS3 devices with external probe setup guidance
- Drag-and-drop device sorting in "All Rooms" view
- First-time user guidance for asset management
- Real-time network status monitoring
- Enhanced data dashboard with orientation adjustment
- Bug fixes
v1.1.1
MOCREO Smart App ·
New Features
- Supports LS2
- ST8 supports data calibration
Improvements
- Optimizes login timeout issue
Bug Fixes
- Corrects text errors on some pages
- Fix known issues.
v1.1.0
MOCREO Smart App ·
New Features
- Pre-sales consultation and quick exchange options
- Support for app usage without login
- Compatibility with temperature sensor ST8
- View relative signal strength of Hub and devices
- Expanded member permissions for family invitations
- Sync measurement data by proximity to the device
Bug Fixes
- Fix known issues.
v1.0.8
MOCREO Smart App ·
New Features
- Supports H5-PRO,LS1,MS2,SW2
- Allows asset timezone configuration
Improvements
- Optimizes asset address setting
Bug Fixes
- Fix known issues.
v1.0.7
MOCREO Smart App ·
New Features
- Endorse a broader array of device categories (ST9, ST10)
Improvements
- Enhanced user experience.
Bug Fixes
- Fix known issues.
v1.0.5
MOCREO Smart App ·
Improvements
- Enhanced user experience.
Bug Fixes
- Fix known issues.